Skip to content
AutoTyreSize Decode a size

Wheel bearing guide: signs, numbers and fitting

Quick answerHum that rises with speed means a worn wheel bearing; match the number on the old one

Car parts6201 vs 6301Bike and carChecked 13 Nov 2026

Two sealed steel ball bearings and a hub spacer on a workshop bench next to a scooter wheel

A worn wheel bearing usually announces itself as a hum or growl that rises with speed, and the replacement must carry the same number as the old one, such as 6201 or 6301 on many two wheelers. On cars, the front bearings work hardest and are usually a press job at a workshop.

This hub covers bearing types, warning signs, how to read a bearing number, replacement steps for bikes, car front and rear bearings, grease, and what shortens bearing life on Indian roads.

At a glance

  • Main warning signHum or growl that rises with speed and changes on bends
  • Quick checkLift the wheel, rock it top to bottom, spin it by hand
  • Bike and scooter typeSealed ball bearings, often two per wheel
  • Number 6201 or 6301Both 12 mm bore; 63 series is larger and wider
  • GreaseSealed units need none; tapered rollers are repacked
  • ReplaceBoth bearings in a two wheeler wheel together

Wheel bearing pages by model

Two wheeler bearings are sold by number, so the model pages list the number and position for each wheel.

Wheel bearing model pages
PageWhat it covers
Activa front wheel bearing numberBearing number for the front wheel of this scooter, how many it uses, and how to check for play

More model pages are on the way. For any other bike, scooter or car, the steps below show how to read the number on the old bearing and what to ask for.

What a wheel bearing does

A wheel bearing lets the wheel spin freely on its axle or hub while carrying the full weight of the vehicle, the braking force and the side loads in corners. Inside a steel outer ring and inner ring, a row of hardened balls or rollers runs in grease, sealed from water and dust. When the grease washes out or the seal fails, the rolling surfaces pit and the bearing starts to hum, then grind, and finally develops play.

A badly worn wheel bearing is a safety issue. It can overheat, let the wheel wobble, upset the brakes and, in the worst case, seize. Treat any of the warning signs below as a reason to see a mechanic soon.

Types: ball, tapered roller and hub units

TypeWhere you find itService
Deep groove ball bearing, sealedFront and rear wheels of most bikes and scooters, often two per wheel with a spacerNot regreased; replaced as a pair when worn
Tapered roller bearingOlder cars, many commercial vehicles and some rear wheelsCleaned, packed with wheel bearing grease and adjusted for preload
Double row bearing pressed into the knuckleFront wheels of many hatchbacks and sedansPressed out and in with a press; not regreased
Hub unit (bearing and hub as one)Many modern cars, often at the rearReplaced as a complete bolt on unit

The front wheel bearing on a car usually works harder than the rear, because it carries the engine weight and the steering and braking loads. A rear wheel hub bearing on a car with rear drums is often part of the drum or hub, and some are replaced together with it.

Wheel bearing noise and other warning signs

  • Hum or growl that rises with speed: the classic sign. It sounds like tyre noise on rough concrete but does not change with the road surface.
  • Noise that changes on bends: if the hum gets louder when you turn one way and quieter the other way, the bearing on the side taking the load is the likely culprit.
  • Play in the wheel: with the wheel off the ground, grip it at the top and bottom and rock it. A clunk or movement means wear.
  • Rough spin: spin the lifted wheel by hand. A healthy bearing spins quietly and evenly; a worn one feels gritty or rumbles.
  • Uneven tyre wear or a vague steering feel: often blamed on alignment first, but a loose bearing can cause it too.
  • ABS warning light: on some cars the ABS sensor ring is part of the bearing, and a failing bearing can trigger the light.
If a wheel bearing is grinding, the wheel has visible play, or the hub is very hot after a short drive, do not continue a long journey. Drive slowly to the nearest workshop and have it inspected.

Reading a wheel bearing number

Most two wheeler wheel bearings are standard metric ball bearings with a four digit number stamped on the side, such as 6201 or 6301. The number tells the counter staff exactly what you need.

How a ball bearing number reads
Part of the numberMeaning
First digit 6Single row deep groove ball bearing
Second digit (2, 3 and so on)Series: a higher number means a thicker, stronger bearing for the same bore
Last two digits 0010 mm bore
Last two digits 0112 mm bore
Last two digits 0215 mm bore
Last two digits 0317 mm bore
Last two digits 04 and upMultiply by 5 for the bore, so 04 is 20 mm and 05 is 25 mm
Letters after the numberSeals or shields; for a wheel, choose a sealed bearing, the same as the old one

So a 6301 and a 6201 both fit a 12 mm axle, but the 6301 is larger outside and wider. They are not interchangeable. Always match the full number on the old bearing, or the one the parts list gives for your model.

Wheel bearing bike and scooter replacement

  1. Raise the wheel you are working on clear of the floor, using the main stand or a paddock stand.
  2. Remove the axle, brake parts and wheel, noting the order of spacers and washers.
  3. Drive out the old bearings from the inside with a drift, working evenly around the inner ring. Keep the centre spacer.
  4. Clean the hub bore and check it for scoring or a loose fit.
  5. Press the new bearing in by its outer ring only, with a socket of the right size, until it seats square.
  6. Fit the spacer and the second bearing, then refit the wheel and torque the axle nut to the figure the manual gives.
  7. Spin the wheel and check the brake works before riding.

Replace both bearings in a wheel together. A bearing driven out with a drift should not be reused. Many riders prefer to let a mechanic do this, because a bearing pressed in crooked fails quickly.

Front wheel bearing and rear wheel bearing on cars

On most cars, front bearings are pressed into the steering knuckle and need a hydraulic press and the right adaptors. That is a workshop job. A rear wheel bearing on many small cars sits inside the brake drum or comes as a hub unit that bolts on. Either way, have the wheel alignment checked after front suspension or knuckle work, because the knuckle is taken off the car.

The wheel axle bearing on rear wheel drive vehicles, such as some pickups and utility vehicles, sits at the outer end of the rear axle. A leaking axle seal can contaminate both the bearing and the rear brakes, so a wet patch on the inside of a rear wheel is worth checking.

Wheel bearing grease: when and which

Sealed ball bearings and hub units come filled for life. Do not pry the seals off to add grease; you will let dirt in. Tapered roller bearings are different: at service they are cleaned, inspected and packed with fresh wheel bearing grease, then adjusted. Use only grease sold for wheel bearings, which resists heat from the brakes and does not wash out easily, and follow the grade in the service manual.

Do not mix grease types, and do not overpack the hub; too much grease heats up and pushes past the seal onto the brakes.

What shortens bearing life on Indian roads

  • Waterlogged roads: riding or driving through deep water forces water past the seals. If you often cross flooded streets in the monsoon, expect to check bearings sooner.
  • Pothole and kerb impacts: a hard hit can dent the rolling track, which starts noise weeks later.
  • Pressure washing: a jet aimed straight at the hub pushes water into the seal. Keep the nozzle away from wheel centres.
  • Overloading: carrying more people or cargo than the vehicle is built for loads the bearings past their design.
  • Wrong fitting: hammering a new bearing in by the inner ring damages it before it turns once.

Tyres matter too. A wheel that is out of balance hammers the bearing at highway speed, so get balancing done with every tyre change; see wheel alignment and balancing. For other wear parts, read our brake pad guide, or browse all topics from the start page.

Questions owners ask

What are the signs of a bad wheel bearing?

Listen for a hum or growl that rises with speed and changes when you turn. Lift the wheel and rock it at the top and bottom; any clunk or play points to a worn bearing. Have a mechanic confirm it.

Can I drive with a noisy wheel bearing?

Just far enough to reach a workshop, at low speed. A bearing that is grinding or has play can overheat and in the worst case let the wheel seize or wobble.

What does 6201 2RS mean?

6201 is a single row ball bearing with a 12 mm bore. The letters after the number describe seals on the sides. Match the full marking on your old bearing or the number listed for your vehicle.

Should I replace wheel bearings in pairs?

On a bike or scooter wheel, replace both bearings in that wheel together. On a car, replace the worn one; many mechanics also change the other side of the same axle if it has similar mileage.

Does a wheel bearing need grease?

Sealed ball bearings and hub units do not; they are filled for life. Tapered roller bearings on some cars and commercial vehicles are cleaned and packed with wheel bearing grease at service.

Why do my wheel bearings fail early?

Common causes are water from flooded roads or pressure washing, pothole hits, overloading and a bearing pressed in the wrong way. Fixing the cause matters as much as fitting a new part.

Every page in this guide 1

PageQuick answer
Activa wheel bearing6201 bearing, 12 x 32 x 10 mm, two in the Activa front wheel