Skip to content
AutoTyreSize Decode a size

PCD calculator for wheels and flanges

Quick answerPCD = distance between neighbouring hole centres divided by sin(180 / number of holes)

Wheels3 to 8 holesWheels and flangesChecked 13 Nov 2026

This PCD calculator turns one ruler measurement into the pitch circle diameter of a wheel hub or flange: choose how many holes it has, enter the distance between the centres of two neighbouring holes, and read the result in millimetres. The maths behind it is a single formula, shown below with worked examples.

We built it for the moment at the wheel shop when an alloy looks right but nobody is sure of the bolt pattern, and for students and fitters marking holes on a flange. If you want the meaning of the term first, read PCD full form.

At a glance

  • FormulaPCD = neighbouring hole gap / sin(180 / holes)
  • 3 hole factorGap x 1.1547
  • 4 hole factorGap x 1.4142, or measure opposite holes directly
  • 5 hole factorGap x 1.7013
  • 6 hole factorGap x 2, or measure opposite holes directly
  • UnitsEnter mm, read mm

How to use the PCD calculator

  1. Choose the number of holes on the wheel, hub or flange. Count studs on the car if the wheel is off.
  2. Enter the gap between the centres of two holes that sit next to each other, in millimetres. Take it with a vernier caliper if you have one.
  3. Read the result. The figure shown is the pitch circle diameter in mm. Round it to the nearest standard wheel pattern, such as 100 or 114.3.

If your reading lands between two standard patterns, measure again on a different pair of holes. A one millimetre error in the gap becomes about 1.4 mm on a four hole wheel and 1.7 mm on a five hole wheel, so a careful measurement matters.

The PCD formula and how to calculate PCD by hand

All the holes sit on one circle, spaced evenly. Two neighbouring holes and the centre of the circle make a triangle, and simple trigonometry links the gap between the holes (a chord) to the diameter:

PCD = gap / sin(180 / n), where n counts the holes and the angle is worked in degrees.

That one line is the full PCD calculation formula. The table gives the multiplier for each common hole count so you can work it out with a phone calculator.

Holessin(180 / n)Multiply gap by
30.86601.1547
40.70711.4142
50.58781.7013
60.50002.0000
80.38272.6131

Worked examples: 3 hole and 4 hole PCD formula

Four holes. You measure 70.7 mm between two neighbouring hole centres on a hatchback wheel. 70.7 x 1.4142 = 99.98, so the wheel is a 4 x 100 mm pattern. Check it the easy way too: on any even hole count, the distance from one hole centre straight across to the opposite hole centre is the PCD itself.

Three holes. Some small vehicles and many machine parts use three holes. A gap of 60 mm gives 60 x 1.1547 = 69.3 mm. With an odd count you cannot measure straight across, so the formula is the only quick route.

Worked example: five hole wheels

Five hole hubs are common on SUVs and MPVs, and they confuse people because no hole faces another. Say the neighbouring gap reads 67.2 mm. 67.2 x 1.7013 = 114.3 mm, so the pattern is 5 x 114.3, the same circle as 4.5 inches.

A second check works without any table: pick any hole, skip the one beside it, and take the centre to centre reading to the next. Multiply by 1.0515. On a 114.3 mm circle that skip one distance is about 108.7 mm. If both checks agree, you can trust the number.

Flange PCD formula and hole marking

Pipe and machine flanges use exactly the same idea, so the flange PCD formula is the same as for wheels. People also ask about the flange PCD full form; it is still pitch circle diameter.

To mark holes on a blank, use the PCD hole marking formula. Take the radius R = PCD / 2 and the angle step 360 / n. Each hole centre sits at x = R cos(angle) and y = R sin(angle) from the flange centre.

HoleAnglex (mm)y (mm)
1075.00.0
26037.565.0
3120-37.565.0
4180-75.00.0
5240-37.5-65.0
630037.5-65.0

The table is a six hole flange on a 150 mm PCD. Neighbouring holes end up 75 mm apart, which the calculator confirms: 75 x 2 = 150.

Using the PCD hole distance result at a wheel shop

Once you have the number, write it as holes x PCD, such as 4 x 100. Then ask the seller for the same figure on the alloy you like. A wheel a few millimetres off will not seat flat on the hub, even if the nuts thread on. Also confirm centre bore, offset and the nut or bolt type before paying. Our alloy wheels guide explains each of these, and the wheel size page helps with diameter and width.

A wheel that needs force to sit on the hub is the wrong wheel. Do not drive on it; ask a wheel shop to check the pattern.

Common mistakes when measuring

  • Reading from the outer rim of one hole across to the opposite side of its neighbour. That adds one hole diameter to the reading.
  • Measuring on a worn or damaged hole that has been elongated by loose nuts.
  • Using a cloth tape, which sags. A steel rule or caliper is much better.
  • Mixing inches and millimetres. Enter millimetres; if you measured in inches, multiply by 25.4 first.
  • Rounding too early. Keep one decimal place until you read the result.

Questions owners ask

How to calculate PCD of a 4 hole wheel without a calculator?

Lay a rule from hole centre to the hole facing it across the hub. That straight line is the PCD, because it passes through the hub centre.

What is the 4 hole PCD formula?

PCD = neighbouring gap x 1.4142, which is the same as dividing the gap by 0.7071. A gap of about 70.7 mm means a 100 mm PCD.

What is the 3 hole PCD formula?

PCD = neighbouring gap x 1.1547, since sin 60 is 0.866. Three hole patterns have no opposite hole, so the formula is the quickest method.

Can I use the calculator for pipe flanges?

Yes. The geometry is the same for any ring of evenly spaced holes, so the flange PCD formula and the wheel formula are identical.

My result is 101.5 mm. Is that 4 x 100?

Probably, but measure again on another pair of holes with a caliper. If you keep getting a figure between two patterns, have a wheel shop check it with a PCD gauge before buying wheels.