Skip to content
AutoTyreSize Decode a size

Thar wheel arch cladding: care, repair and replacement

Quick answerBlack plastic flares around each wheel; replace a cracked piece as a genuine part

Car partsClips and screwsCheck tyre rubChecked 13 Nov 2026

Independent owner guide. Not affiliated with Mahindra. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

The Thar wheel arch cladding is the black plastic flare that frames each of the four wheel openings on the 3 door Thar, protecting the painted body from stones, mud and branches. It is held on by clips and screws, so a cracked or loose piece can be replaced on its own without painting the fender.

Owners come to us for cladding after a scrape on a narrow lane, after a trail where a branch tore a clip out, or when bigger tyres start to rub. Each case is covered below.

Thar fitment card

Tyre size
255/65 R18 (AXT, LXT), 255/60 R19 (ZXT) on the current Thar OG
Wheels
18 inch steel (AXT), 18 inch alloy (LXT), 19 inch diamond cut alloy (ZXT)
Earlier base version
245/75 R16 on 16 inch steel wheels (AX, earlier AXT)
Earlier top version
255/65 R18 on 18 inch alloy wheels (LX, earlier LXT)
Tyre pressure (cold)
About 32 psi front and rear; the door sticker figure for your tyre rules
Spare
Full size on the tailgate: steel on AXT and LXT, alloy 255/60 R19 on ZXT
Front fog lamps
Not on AXT; fitted on LXT; LED with cornering function on ZXT
Black plastic wheel arch flare above a muddy all terrain tyre on a boxy 3 door off road SUV
The black flares take stone hits so the Thar body paint does not

What Thar wheel arch cladding does

A Thar runs on 255 mm wide tyres that throw stones and slush outward. The cladding takes those hits instead of the paint. It also covers the body edge where the fender meets the arch liner, which is where rust starts on vehicles that cross water often. On an off road jeep the cladding is meant to take damage; a scuffed flare is normal wear, not a defect.

How the arch cladding is fixed

Each flare is held by a mix of push clips along the outer edge and screws inside the arch. Some fasteners are reached only after turning the steering fully or removing the wheel. Plastic clips break when pulled cold, so on a winter morning warm the area in the sun first, and use a trim removal tool rather than a screwdriver to avoid marking the paint.

Replacing a damaged Thar flare

  1. Note the corner it belongs to; left and right flares are mirror images and do not swap.
  2. Ask the dealer for the genuine part with your VIN, since shapes can differ between the earlier Thar and the Thar OG.
  3. Buy a fresh set of clips with it; old clips rarely hold again.
  4. Clean mud from the body edge and check for rust before fitting.
  5. Fit the top screws loosely, line up the flare, then press in all clips and tighten.

Aftermarket wide flares are sold too. Check the fit and that they still cover the full tread width, since a tyre that sticks out past the body can fail fitness checks.

Tyre clearance after an upgrade

Bigger tyres are the most common reason for rubbing at the cladding. The factory sizes, 255/65 R18 and 255/60 R19, are both about 789 mm tall. A larger tyre or a rim with more negative offset pushes the tread toward the flare. Turn the wheel fully left and fully right while the jeep carries a load, then drive slowly over a speed breaker at an angle and listen. Rubbing marks on the inner face of the cladding confirm it. The sizes are explained on Thar tyre size and rims on Thar OG alloy wheels.

Keeping black plastic from fading

Strong sun turns black plastic grey over time. Clean it with water and a little soap, dry it, then use a plastic restorer meant for exterior trim. Avoid tyre shine products on the cladding, as many contain solvents that leave a greasy layer that catches dust. After beach drives, rinse salt off the arches the same day.

Cleaning mud behind the cladding

After a muddy trail, clay packs into the gap between flare and body. It holds water against the steel and adds weight that can unbalance the wheel. Use a garden hose, not a high pressure jet aimed straight at the clips, and remove any mud packed onto the inside of the rim as well. If the steering shivers around 80 km/h after a trail, cleaning the rim often cures it before any balancing.

Other models and kit types are on our wheel arch cladding page. For a crossover style kit, see the Brezza wheel arch kit.

Questions owners ask

Does every Thar have wheel arch cladding?

Yes, the 3 door Thar has black flares around all four wheel openings. Shapes and fasteners can differ between the earlier Thar and the Thar OG, so order parts with your VIN.

Can I replace one Thar flare on its own?

Yes. Each flare is a separate part held by clips and screws, so a damaged one can be swapped without touching the others or repainting.

Why does my Thar tyre rub the cladding?

Usually because of larger tyres or rims with more negative offset than stock. Check at full steering lock and over angled speed breakers, and go back toward the factory size if it rubs.

Are wider aftermarket flares worth fitting?

Only if you fit wider tyres that stick out past the stock flare. Choose a set that matches the factory mounting points and covers the full tread.

How do I stop the cladding from turning grey?

Wash it gently, then apply an exterior trim restorer every few months. Avoid solvent based tyre shine, which attracts dust.