Skip to content
AutoTyreSize Decode a size

Brezza wheel arch kit and cladding guide

Quick answerGenuine silver wheel arch garnish fits all current Brezza variants; four pieces

Car partsAll variantsSilver or blackChecked 13 Nov 2026

Independent owner guide. Not affiliated with Maruti Suzuki. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

A Brezza wheel arch kit is a set of four trim pieces, two for the front arches and two for the rear, that sit over the black plastic around each wheel opening. Maruti Suzuki lists a silver wheel arch garnish for the current Brezza in all variants, and a premium silver version that comes with a fitting manual, a paper template and a small tab tool.

The kit changes the look of the side profile and adds a layer of protection where stones and mud hit hardest. It does not change any tyre or wheel size, so your 215/60 R16 tyres and 16 inch wheels stay as they are.

Brezza fitment card

Tyre size
215/60 R16 on every current variant, LXi to ZXi+
Wheels
16 inch steel with covers (LXi, VXi petrol), 16 inch alloy (ZXi, ZXi+)
Tyre pressure (cold)
Front 33 psi, rear 33 psi at normal load
Full load front
36 psi front; read the door sticker for the loaded rear figure
Earlier Vitara Brezza
205/60 R16 on LDi, VDi, LXi, VXi; 215/60 R16 on ZDi, ZXi and plus trims
PCD (Vitara Brezza)
5 x 114.3 mm, 60.1 mm centre bore, M12 x 1.25 nuts
Wiper blades
24 inch driver side, 16 inch passenger side
Wheel cap
16 inch, on steel wheel variants
Front fog lamps
LED fog lamps on ZXi+; lower trims have blank inserts
Silver trim garnish fitted along the front wheel arch of a compact SUV with black cladding
A silver garnish strip over the black plastic around the front wheel arch

What the Brezza wheel arch kit includes

Genuine arch garnish options for the Brezza
ItemFitsIn the box
Wheel arch garnish, silverCurrent Brezza, all variantsFour arch pieces
Wheel arch garnish, premium silverBrezzaTwo front and two rear pieces, manual, paper template, tab tool

The accessory range also mentions black finishes for arch trims on this model. Ask the parts counter which colour matches your body paint and the factory lower trim. A silver finish lifts darker paint shades, while black blends in on lighter colours.

Cladding, garnish and kit: the words explained

Shops use these terms loosely. Cladding usually means the thick black plastic moulded around the arches and lower doors from the factory. Garnish is a thinner decorative strip fixed on top of that cladding. A kit is simply the set of four garnish pieces sold together. When you ask for Brezza wheel arch cladding at a parts shop, be clear whether you want a replacement factory piece or an add on garnish.

Fitting the garnish on your Brezza

  1. Wash the arch area and let it dry fully. Wipe the surface with an alcohol wipe to remove wax.
  2. Hold each piece against its arch without removing the tape backing. Sort out which garnish goes on which corner of the Brezza before any tape comes off.
  3. Use the paper template, if supplied, to mark where the clips or tabs go.
  4. Peel the tape a little at a time, starting at the top of the arch, and press as you go.
  5. Leave the car in the shade for a day before washing or driving through heavy rain.

Warm weather helps the tape grip. In a cold north Indian winter, warm the tape gently with a hair dryer first.

Does a wider arch let me fit bigger tyres

No. The garnish sits on the outside of the existing arch. It does not create more room inside the wheel well, so it does not change which tyres will clear the body at full steering lock or full suspension travel. If you are thinking about larger rims, read the Brezza alloy wheels page and the upsize maths on the Brezza tyre size page first.

Protection on village roads and highways

Gravel flicked up by the front tyres chips paint on the arch lips and lower doors. A garnish takes those hits, and a scratched piece can be swapped alone. On ghat roads and broken village lanes, mud packs into the arch edges. Hose the arches out after such trips so wet mud does not sit against the metal and start rust at the seams.

Signs a garnish needs attention

Look for a lifting edge, a rattle over speed breakers, or water collecting behind a piece. A lifted edge catches wind at highway speed and can tear off. Re-stick it with fresh automotive tape, or ask the workshop to refit it. If a factory cladding clip has broken after a kerb scrape, a replacement clip from a parts shop usually fixes it.

Keep the template and the tab tool from the box. They make it easy to refit a piece after body repair.

For other models, see the wheel arch cladding guide or compare with the Fronx wheel arch garnish page.

Questions owners ask

Is there an official Brezza wheel arch kit?

Yes. Maruti Suzuki lists a silver wheel arch garnish for all current Brezza variants, and a premium silver set with fitting aids. Your dealer can confirm current stock.

How many pieces are in the Brezza wheel arch cladding set?

Four: one for each wheel arch, two front and two rear.

Does the arch kit need drilling?

The genuine garnish uses adhesive tape and tabs, with a paper template to position it. No drilling is needed for that kit.

Will the garnish fit the earlier Vitara Brezza?

The listings name the current Brezza. The earlier car has a different body shape, so ask for a part made for that version.

Can I wash the car normally after fitting?

Wait a day for the tape to cure. After that, a normal wash is fine, though avoid holding a pressure washer nozzle close to the edges.