Pick a 12 inch Eon wheel cap for the base trims on 12 inch rims and a 13 inch one for Magna, Sportz and later cars on 13 inch rims. Hyundai gave the entry D-Lite small hub caps over silver steel wheels, while the Magna and above wore full face covers.
With Eon production over, replacement covers mostly come from a parts shop these days. Getting the size right first saves you a return trip.
Eon fitment card
- Tyre size
- 145/80 R12 on base versions, 155/70 R13 on Magna, Sportz and most later trims
- Wheels
- 12 inch or 13 inch steel; hub caps on base trims, full covers on Magna and up
- Tyre pressure (cold)
- Front 33 psi, rear 33 psi; 36 psi all round at full load
- Wheel cap
- 12 inch or 13 inch, to match the R number on the tyre
- Wiper blades
- 22 inch driver side, 14 inch passenger side (check the old blades)
- Status
- No longer sold new

Hyundai Eon wheel cap size table
| Variant group | Tyre | Factory dress | Cover to buy |
|---|---|---|---|
| D-Lite, Era, LPG base | 145/80 R12 | Hub caps | 12 inch |
| Era Plus | 155/70 R13 in most cars | Varies | 13 inch, check tyre |
| Magna, Sportz, 1.0 Kappa | 155/70 R13 | Full wheel cover | 13 inch |
Finding your rim size in ten seconds
Crouch beside the Eon and look at the tyre lettering. The code ends in R12 or R13, and that last number is the rim, so it is the cover size too. Never trust the old cover alone; an earlier owner might have bought a wrong one, which explains why it kept slipping. Our wheel cap size guide walks through this for all cars.
Fitting a full cover on an Eon steel rim
- Wipe dust off the rim lip, since grit keeps the clips from biting.
- Check the steel ring on the back sits inside all the plastic hooks.
- Align the notch over the valve stem; forcing a cover over the valve can snap the valve stem.
- Seat the twelve o'clock section first, then tap around with open hands.
- Pull lightly at the rim edge to confirm it holds.
Why Eon covers fly off
A full cover on a small car takes a beating from speed breakers, broken edges and kerbs during tight parking. Covers usually drop off when the retaining ring has lost its spring after being prised off with a screwdriver at a puncture shop. Request that the fitter pulls it free gently near the valve. Some owners loop a slim cable tie through a vent and the rim slot for insurance. Never drive on with a cover hanging, since it can scrape the tyre wall.
Choosing a replacement Eon wheel cap
Plenty of 12 and 13 inch covers are sold for small hatches. Look for these before paying:
- Flexible plastic that bends without a white stress mark.
- A metal ring, not just plastic tabs.
- Air slots, so heat from the brakes can leave on long descents.
- Four matching pieces, since odd designs look scruffy.
Original covers from a Hyundai parts counter fit snugly but cost more, because they are made for this exact rim. Market covers vary in grip.
Hub caps on base trims
The base Eon has only a small hub cap that clips into the middle of the pressed rim. If one is missing, the hub nut area rusts faster in the monsoon. A parts shop can match it by holding it against the wheel centre. Many base car owners instead fit 12 inch full covers, which hide rust on the steel rim and make the car look a trim higher.
Covers, tyres and other Eon guides
When you upgrade from 12 to 13 inch wheels, you will need 13 inch covers too. Our Eon tyre size guide deals with the rubber for that swap, and Eon tyre pressure gives the air. Browse more models from the wheel cap section, such as the Alto 800 wheel cap.
Questions owners ask
What size wheel cap does Hyundai Eon use?
12 inch for cars running 145/80 R12 and 13 inch for cars running 155/70 R13. The R figure on the rubber decides.
Does the Eon Magna have wheel covers?
Yes. The Magna came with full wheel covers over 13 inch steel wheels.
Will a 13 inch cover fit a 12 inch Eon wheel?
No. It will be too big to grip the rim and will fall off. Match cover diameter to rim diameter.
Do full covers suit alloy rims?
No. Full covers are for steel wheels only. Alloys take a small centre cap made for that wheel.
How do I stop my Eon wheel cap falling off?
Replace a bent retaining ring, fit the cover by hand rather than hammering, and add a cable tie through a vent if the roads are rough.