The Brezza tyre size, across every current variant, is 215/60 R16, whether you own a base LXi on pressed steel rims or a ZXi+ with two tone alloys. Maruti Suzuki uses one size on both axles, so all four tyres can swap places during rotation.
Owners of the earlier Vitara Brezza need to look closer. On that car the lower trims (LDi, VDi diesel and LXi, VXi petrol) rolled on a narrower 205/60 R16, while the ZDi and ZXi trims and their plus versions wore 215/60 R16. Below is the full chart, what the code means, safe upsizes with the maths, and when to change the set.
Brezza fitment card
- Tyre size
- 215/60 R16 on every current variant, LXi to ZXi+
- Wheels
- 16 inch steel with covers (LXi, VXi petrol), 16 inch alloy (ZXi, ZXi+)
- Tyre pressure (cold)
- Front 33 psi, rear 33 psi at normal load
- Full load front
- 36 psi front; read the door sticker for the loaded rear figure
- Earlier Vitara Brezza
- 205/60 R16 on LDi, VDi, LXi, VXi; 215/60 R16 on ZDi, ZXi and plus trims
- PCD (Vitara Brezza)
- 5 x 114.3 mm, 60.1 mm centre bore, M12 x 1.25 nuts
- Wiper blades
- 24 inch driver side, 16 inch passenger side
- Wheel cap
- 16 inch, on steel wheel variants
- Front fog lamps
- LED fog lamps on ZXi+; lower trims have blank inserts

Brezza tyre size chart: LXi, VXi, ZXi and ZXi+
Here is what each Brezza trim leaves the factory with. The new Brezza tyre size does not change between petrol, CNG or automatic versions; only the wheel underneath it does.
| Variant | Front | Rear | Wheel |
|---|---|---|---|
| LXi (base model) | 215/60 R16 | 215/60 R16 | 16 inch steel with cover |
| VXi | 215/60 R16 | 215/60 R16 | 16 inch steel with cover |
| ZXi | 215/60 R16 | 215/60 R16 | 16 inch alloy |
| ZXi+ (top model) | 215/60 R16 | 215/60 R16 | 16 inch dual tone machined alloy |
So the Brezza LXi tyre size, the Brezza VXi tyre size and the Brezza ZXi tyre size are all the same 215/60 R16. The Brezza top model tyre size matches the base model tyre size too. Paying more for a higher trim buys a nicer wheel, not a wider tyre. One used car dealer lists 205/65 R16 for the current LXi and VXi, but the spec sheets and most sources say 215/60 R16, so read your own sidewall before ordering.
Earlier Vitara Brezza tyre size: LDi, VDi, ZDi
The first Vitara Brezza was sold with a diesel engine and later with petrol. Its tyre size changed with the trim level, which confuses many second hand buyers.
| Variant | Front | Rear | Wheel |
|---|---|---|---|
| LDi, VDi (diesel) | 205/60 R16 | 205/60 R16 | 16 inch steel |
| LXi, VXi (petrol) | 205/60 R16 | 205/60 R16 | 16 inch steel |
| ZDi, ZDi+ (diesel) | 215/60 R16 | 215/60 R16 | 16 inch alloy |
| ZXi, ZXi+ (petrol) | 215/60 R16 | 215/60 R16 | 16 inch alloy |
That means the Vitara Brezza VDi tyre size is 205/60 R16, while the ZDi tyre size is 215/60 R16. If you bought an older VDi that a past owner fitted with alloys, the tyres on it may be either size. The sidewall is the only honest answer.
Reading 215/60 R16 on a Brezza sidewall
Each part of the code tells you something useful at the tyre counter:
- 215: Brezza tread width, 215 mm sidewall to sidewall.
- 60: aspect ratio; multiply 215 by 0.60 and the Brezza sidewall comes to about 129 mm.
- R: a radial carcass, standard on Indian passenger cars.
- 16 is the rim diameter. This is the Brezza tyre size in inches that owners ask about: a 16 inch wheel.
Next to the size sits a two digit load code and one speed letter. Copy whatever is printed on your factory tyre and never go lower on either one. The DOT date code and the rest of the Brezza sidewall markings are decoded in our sidewall reading guide.
Brezza wheel size, plus full tyre height in mm
The Brezza wheel size is 16 inches on every version, old and new. What changes the feel of the car is the full height of the tyre, rim plus two sidewalls:
- 215/60 R16 works out to 406.4 plus twice 129, near 664 mm overall
- 205/60 R16 works out to 406.4 plus twice 123, near 652 mm overall
The 215 tyre on newer cars stands about 12 mm taller and has a wider contact patch. Many earlier VDi owners move up to 215/60 R16 when the old set wears out. That is the size Maruti Suzuki itself fitted on the ZDi of the same body, so the arches already have room for it. Expect the speedometer to read slightly lower than before, by under 2 percent.
Bigger Brezza tyres that hold the stock height
Owners often want 17 or 18 inch wheels for looks. Stay within roughly 3 percent of the 664 mm stock height so the Brezza speedo, ABS sensors and gearing keep reading true. Here is how common sizes compare:
| Size | Height | Difference |
|---|---|---|
| 215/55 R17 | 431.8 + 236.5 = 668 mm | +0.6 percent |
| 225/50 R17 | 431.8 + 225 = 657 mm | -1.1 percent |
| 215/50 R18 | 457.2 + 215 = 672 mm | +1.2 percent |
| 205/65 R16 | 406.4 + 266.5 = 673 mm | +1.3 percent |
Fitting is not just about height. Any new rim has to share the hub stud pattern, bore and offset, and the tyre's load index must not drop below the factory one. Short sidewalls send speed breaker jolts straight to the cabin, and a wider one can rub at full steering lock. Maruti Suzuki does not fit a 17 inch wheel on any Brezza, so treat these as your own risk. Your insurer must be told about modified wheels. The Brezza alloy wheels page covers the wheel side.
Spare tyre and rotation on the Brezza
Lift the boot floor and inspect the spare on day one, and check its pressure each month. A flat spare discovered on a dark highway shoulder helps nobody. Since front and rear sizes match, rotate all four every 8,000 to 10,000 km. The front tyres on a front wheel drive SUV like this wear faster at the shoulders, especially if you drive a lot on ghat roads or take sharp U turns in city traffic.
Ask for a wheel alignment during that rotation if the Brezza drifts to one side or its steering wheel sits crooked on a level road.
When a Brezza needs new tyres
Change the set when the Brezza tread wears level with the small raised bars inside the main grooves, about 1.6 mm deep. For monsoon driving, many owners change earlier at about 3 mm, because water clearance drops fast on a worn tyre. Look also for cracks in the sidewall, bulges after a pothole hit, and age. Tyres older than five or six years harden even with tread left.
Once the new set is on, fill it to the figures on our Brezza tyre pressure page. For other cars, start at the car tyre size hub.
How the Brezza compares with rivals
The Nexon tyre size page shows the same 215/60 R16 on its upper variants and 195/60 R16 on lower ones. Most trims listed on our Venue tyre size chart also run 215/60 R16. A Brezza owner shopping for tyres will find that size in stock at almost any tyre shop, which helps when you need a single replacement in a small town.
Questions owners ask
What is the Brezza tyre size?
Every current Brezza uses 215/60 R16 at both ends. That covers LXi, VXi, ZXi and ZXi+ with petrol, CNG or automatic gearboxes.
What is the Vitara Brezza tyre size?
The earlier Vitara Brezza used 205/60 R16 on LDi, VDi, LXi and VXi, and 215/60 R16 on ZDi, ZXi and their plus trims. Check your own sidewall, as past owners may have changed size.
Does a Brezza ZXi take a different tyre than a VXi?
No. Both use 215/60 R16. Only the rim differs: alloys on the ZXi, covered steel on the VXi petrol, with identical rubber on both.
What is the Brezza tyre size in inches?
The wheel is 16 inches across. The whole tyre stands about 664 mm tall, which is roughly 26 inches.
Will a VDi from the earlier Vitara Brezza take 215/60 R16?
Yes, this is a common change because the ZDi of the same car came with that size. The speedometer will read a little low, by less than 2 percent. Ask the shop to balance and align after fitting.
Is 205/65 R16 right for the Brezza?
It stands roughly 1.3 percent taller than stock, so it stays within limits. It is not the factory size on current cars though, so prefer 215/60 R16 for matching grip and handling.