Skip to content
AutoTyreSize Decode a size

XUV 3XO Alloy Wheels by Variant

Quick answer16 inch alloys on AX5, AX5 L and REVX A; 17 inch diamond cut alloys on AX7 and AX7 L

WheelsDiamond cut finishSteel on MXChecked 13 Nov 2026

Independent owner guide. Not affiliated with Mahindra. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

The 3XO alloy wheels measure 16 inch across the AX5, AX5 L and REVX A, wearing 205/65 R16, and grow to 17 inch for the two AX7 trims, which wear 215/55 R17. MX trims and the REVX M roll out on pressed steel 16 inch rims hidden under plastic trims.

Most owners who ask about alloys drive one of those steel wheel cars and want to upgrade. Helpfully, Mahindra already offers two alloy diameters on this body, so an upgrade path exists. Here is what to buy and what to check.

XUV 3XO fitment card

Tyre size (MX, REVX, AX5)
205/65 R16
Tyre size (AX7, AX7 L)
215/55 R17
Wheels
16 inch steel with covers (MX, REVX M), 16 inch alloy (AX5, REVX A), 17 inch alloy (AX7)
Spare
135/90 R16 steel space saver, for short emergency use
Tyre pressure (cold)
See the driver door sticker or owner's manual
Replaced
XUV300, which used its own pages on this site
A two tone 17 inch diamond cut alloy wheel with tyre leaning against a workshop wall
A diamond cut alloy needs gentle washing to protect its clear coat

Factory wheels on the XUV 3XO

VariantWheelTyre
MX1, MX2, MX2 Pro, MX3, MX3 Pro16 inch steel (covers on MX3)205/65 R16
REVX M, REVX M(O)16 inch steel with black cover205/65 R16
REVX A16 inch alloy205/65 R16
AX5, AX5 L16 inch diamond cut alloy205/65 R16
AX7, AX7 L17 inch diamond cut alloy215/55 R17

Every trim keeps a pressed steel 135/90 R16 temporary spare under the floor. It stays the same even on AX7 cars, so a 17 inch alloy is never in the boot.

Upgrading an MX to 3XO alloy wheels

The simplest step is a 16 inch alloy with your existing 205/65 R16 tyres. Nothing about the speedometer, ride height or steering lock changes, and you can move the tyres across at a wheel shop. Ordering genuine AX5 rims through a Mahindra dealer removes the guesswork, as they are built around this hub.

Going to 17 inch with 215/55 R17 copies the AX7 setup. Height shifts by under 1 percent, leaving the instruments true. You pay for four new tyres as well as the wheels, and the ride turns firmer over rough village roads.

What must match on any aftermarket wheel

  • PCD: the count of wheel studs on the 3XO hub and the diameter of their circle. We have not verified the 3XO number, so look for it cast inside a factory rim or ask the service desk, then cross check with the PCD calculator before buying.
  • Centre bore: the middle hole must hug the hub spigot, using a spacer ring if needed, or the steering trembles at 100 km/h.
  • Offset: too far out and the tyre rubs the wheel arch on full lock; too far in and it can touch the strut.
  • Load rating: the wheel must carry the car fully loaded.
  • Diameter: keep the tyre's overall size within about 3 percent of stock.

Bigger than 17 inch?

Accessory dealers do push 18 inch sets for the 3XO. That needs a very low profile tyre to keep the diameter, and the thin sidewall leaves the rim exposed to potholes and speed breaker edges. Bent rims and cracked alloys are a common repair on such setups. Your warranty may also not cover suspension parts damaged after a non standard wheel change, and your insurer must be told. For daily Indian roads, 16 or 17 inch is the sensible limit.

Caring for diamond cut alloys

The AX5 and AX7 wheels have a machined bright face over a dark base, protected by a clear lacquer. Diluted shampoo and a microfibre mitt are enough; stiff brushes and acidic sprays do harm. Brake dust is hot iron; leaving it for weeks lets it bite through the lacquer. Once the clear coat chips, moisture spreads beneath and the silver face goes cloudy. Touch up paint cannot hide a kerb rash on this machined face; the cure is a fresh lathe pass and new lacquer, which shaves metal each time, so a wheel tolerates only a few such passes. Repair options are compared on diamond cut alloy wheels.

Signs a 3XO alloy needs attention

A steering shake that starts around a fixed speed often means a wheel weight has fallen off or a rim is bent. A tyre that loses air slowly with no nail in it may be leaking at a crack or at a corroded bead seat. After a hard pothole hit, ask the tyre shop to spin the wheel on the balancer and look for run out. Do not drive long distance on a cracked alloy; have it inspected first.

Questions owners ask

What size are XUV 3XO alloy wheels?

The AX5, AX5 L and REVX A have 16 inch alloys. The AX7 and AX7 L have 17 inch diamond cut alloys as standard.

Does the 3XO MX3 have alloy wheels?

No. The MX3 and MX3 Pro use 16 inch steel wheels with covers. You can add 16 inch alloys and keep the same tyres.

Will AX7 17 inch wheels fit an AX5?

The maker fits them on the same body, so they fit. You need 215/55 R17 tyres to go with them.

Should a 3XO owner move to 18 inch rims?

Mahindra does not offer that diameter. Low profile tyres would be needed and the rims become easy to damage on Indian roads. We advise staying at 16 or 17 inch.

Is the spare an alloy wheel?

No. Every variant keeps a narrow 135/90 R16 steel temporary spare for short distances.

How do I fix a scratched diamond cut alloy?

Light marks can be polished, but a kerb scrape needs a lathe re-cut and fresh lacquer at a wheel repair shop.