Venue alloy wheels leave Hyundai's plant as 16 inch diamond cut rims on the HX 7, HX 8 and HX 10, as black painted 16 inch rims on Knight editions, and as 17 inch rims for the N Line. Every other Venue leaves the plant on steel rims, either 15 inch with a cover or 16 inch dual tone styled steel.
This page lists which trim gets what, the facts you need before ordering aftermarket rims, how the N Line wheel differs, and and a routine that keeps machined spokes bright through dusty summers and wet monsoons.
Venue fitment card
- Tyre size
- 195/65 R15 (1.2 petrol lower trims), 215/60 R16 (most trims), 215/55 R17 (N Line)
- Wheels
- 15 inch steel with cover, 16 inch styled steel, 16 inch alloy, 17 inch alloy on N Line
- Tyre pressure (cold)
- Read the door sticker; earlier Venue listed 33 psi front and rear
- Spare
- 195/65 R15 steel spare; tyre mobility kit on 1.2 petrol HX 2
- Wheel cap
- 15 inch, on 1.2 petrol trims with steel wheels
- Top model
- HX 10: 215/60 R16 on 16 inch diamond cut alloys

Hyundai Venue alloy wheels by trim
The Hyundai Venue alloy wheels story starts at the HX 7. Lower trims carry steel. Here is the brochure split:
| Variant | Wheel | Tyre |
|---|---|---|
| HX 2, HX 4, HX 5, HX 5+, HX 6T (1.2 petrol) | 15 inch steel with full cover | 195/65 R15 |
| HX 2, HX 5 (turbo petrol, diesel), HX 6 | 16 inch dual tone styled steel | 215/60 R16 |
| HX 7, HX 8, HX 10 | 16 inch diamond cut alloy | 215/60 R16 |
| Knight editions with alloys | 16 inch black painted alloy | 215/60 R16 |
| N Line N6, N10 | 17 inch diamond cut alloy, N emblem | 215/55 R17 |
Notice that the HX 2 and HX 5 turbo or diesel already wear 16 inch wheels, though in painted steel. Swapping those for the HX 8 alloy needs no tyre change, because the tyre size stays 215/60 R16.
Venue N Line alloy wheels
Each of the Venue N Line alloy wheels is a 17 inch machined design wearing an N emblem at its hub and red brake callipers peeking through the spokes. They carry 215/55 R17 tyres. The extra inch of rim, against a lower wall, sharpens steering response, but the ride over broken concrete feels busier than on a 16 inch HX car.
N Line owners should take speed breakers slowly and stay well clear of the sharp edge of a pothole. A cracked or bent 17 inch rim must be checked by a wheel shop before the car goes back on the highway.
New Venue alloy wheels compared with the earlier car
The new Venue alloy wheels keep the 16 inch size used on the earlier SX and SX(O) trims, which also ran 215/60 R16 tyres. So the size is familiar, but the spoke design differs. Picking up second hand rims off an older Venue? Match stud circle, hub hole and offset to your own car before any money changes hands. Our PCD calculator shows a ruler method for the stud circle.
Hyundai does not print the PCD in the Venue brochure, and global wheel sites list different figures for different markets. Measure your own hub, or check the stamp on the back of an original wheel.
Fitting alloys to a 15 inch 1.2 petrol Venue
Many 1.2 petrol owners want alloys. You have two routes. First, an aftermarket 15 inch alloy carrying the same 195/65 R15 rubber leaves speedo and ride untouched. The other is a 16 inch alloy with 215/60 R16, the size Hyundai fits on other trims.
The 16 inch route makes the overall tyre about 30 mm taller, so the speedo reads low by close to 5 percent, and the steering weighs up a little in parking. Hyundai already fits that size to the Venue body, though your insurer should hear about it, and the old steel set should stay in the garage for warranty visits. The Venue tyre size page shows the height maths.
What to check before buying aftermarket rims
- Bolt pattern: must match the Venue hub exactly. A near match wobbles and shears studs.
- Centre bore: the rim's middle hole should hug the Venue hub; if it is larger, a matching spigot ring stops vibration.
- Offset: push the wheel out too far and the 215 mm tyre scrubs the liner at full lock; pull it in and it nears the strut.
- Load rating: match or beat the factory rim, since a fully loaded Venue puts real weight on each corner.
- Width: a much wider rim with a stretched tyre exposes the rim lip to kerbs.
Going past 17 inch on a Venue makes little sense for Indian streets. The wall gets thin, rims bend on potholes, and replacement tyres in odd sizes go out of stock in smaller district towns.
Caring for diamond cut Venue rims
On these Venue rims the shiny face is lathe turned aluminium sealed by a clear coat. When gravel or a kerb breaks through that clear coat, damp gets under it and white powdery corrosion spreads along the spokes. Grey pad dust builds up fast on Venue rims; lift it off during your Sunday wash, using diluted car shampoo on a soft detailing brush. Strong acid wheel sprays strip the lacquer, so keep away from them.
Scuffed Venue rims can be skimmed again on a CNC lathe, though every pass shaves away metal, so only a couple of re-cuts are sensible. How many re-cuts a rim can take is explained under diamond cut alloy wheels. Black painted Knight rims hide dust better but show scratches as silver lines.
Balancing and alignment after a wheel change
Any new rim needs balancing on a machine before fitting, and if the Venue's steering sits crooked after the swap, book an alignment. On Venue alloys the fitter should use adhesive weights tucked behind the spokes, leaving the visible face clean.
Broader advice on finishes and sizes lives in our alloy wheels hub, with a dedicated 16 inch alloy wheels explainer too.
Questions owners ask
Which Venue variant gets alloy wheels?
The HX 7, HX 8 and HX 10 get 16 inch diamond cut alloys. Knight editions with alloys use black painted 16 inch rims, and the N Line N6 and N10 use 17 inch alloys.
Does the Venue HX 5 have alloy wheels?
No. A 1.2 petrol HX 5 rolls on covered 15 inch steel rims, and its turbo or diesel sibling gets 16 inch dual tone styled steel.
Can I fit N Line 17 inch alloys on a regular Venue?
Hyundai bolts them to this very body on the N Line, so they clear the arches, but you also need 215/55 R17 tyres. Check the offset and hub fit, and expect a firmer ride.
Are Venue alloy wheels tubeless ready?
Yes. All Venue wheels, steel or alloy, run tubeless radial tyres from the factory.
Venue alloy got kerbed. Can it be repaired?
Light scratches on painted rims can be touched up. Deep gouges in a diamond cut Venue rim go to a lathe equipped repairer. Any crack in the rim means replacement, not repair.
What is the Venue alloy wheel size?
The factory Venue alloy wheel size is 16 inch on HX trims and 17 inch on the N Line. There is no factory 15 inch alloy on the current car.