The TVS Zest tyre pressure for the Scooty Zest 110 comes to 24 psi for the Zest front tyre and 28 psi for its rear tyre with only the rider aboard, gauged on cold tyres. With a pillion, the rear needs more air, as the table below explains.
These figures are for the TVS scooter only. The Tata Zest sedan shares the name but is a car with its own figure on the driver door pillar, so see the Tata Zest tyre size page if that is what you drive.
Zest fitment card
- Tyre size
- 175/65 R14 on the base XE, 185/60 R15 on XM, XMS, XMA, XT and XTA
- Wheels
- 14 inch steel on XE, 15 inch steel on mid variants, 15 inch alloy on XT and XTA
- Tyre pressure (cold)
- Read the sticker on the driver door pillar or the owner's manual
- Status
- No longer sold new
- Scooty Zest 110 (scooter)
- A different vehicle: 90/100-10 front, 90/90-10 rear, 24 psi front, 28 psi rear solo

Scooty Zest tyre pressure table
| Load | Front | Rear |
|---|---|---|
| Rider alone | 24 psi (1.69 kg/cm2) | 28 psi (1.97 kg/cm2) |
| Rider with pillion | 24 psi | Raise the rear: see your manual |
Scooty Zest front pressure never changes with load. For two-up use, different print runs of the Zest manual list 32 psi or 36 psi behind, so trust whichever your own copy shows. If you have lost it, any TVS service centre can tell you the value for your build.
Why the Zest rear runs higher
On a Scooty Zest the swingarm engine, rider and passenger all sit above that rear 90/90-10. Such a tiny tyre holds little air, so losing even three psi lets it flatten noticeably. A soft Zest rear wallows across humps and runs hot on a long commute. The front tyre carries far less weight, which is why its figure stays low.
Checking TVS Zest tyre pressure the right way
- Gauge the Zest first thing, or after a three hour rest parked in shade.
- Put the scooter on its centre stand on level ground.
- Remove each cap, then seat the gauge squarely on the stem.
- Top up a little at a time, reading again until the Zest shows 24 psi front, 28 psi rear.
- Screw both caps back to keep grit off the valve core.
Filling warm after riding to the pump? Aim 2 psi over the Zest cold numbers and confirm once it cools overnight. Gauge handling tips sit in our pressure checking walkthrough.
Petrol pump air machines and small valves
Many pump machines are set for car tyres and blast in air fast. On a 10 inch scooter tyre that can overshoot by 4 or 5 psi in a second. Ask the attendant to set the digital machine to your number first, and watch the display. A straight chuck struggles to reach a ten inch Zest rim, so roll forward until the stem points at the ground first.
Zest 110 figures in bar, kPa and kg/cm2
The Zest booklet prints kg/cm2; pump displays usually read psi; newer handheld gauges may read bar. On a bar gauge the Zest front reads about 1.65 (165 kPa) and the Zest rear about 1.93 (193 kPa). Convert your pillion value with our tyre pressure converter.
Scooty Zest running soft, or pumped hard
An underfilled Zest scrubs its tyre shoulders, feels heavy turning into a parking slot and risks bending a ten inch rim in a crater. Overfilling flips the problem: the scooter skips over broken tar, the contact patch shrinks on rain soaked roads during the monsoon, and tread vanishes from the middle first. The 28 psi rear figure is a balance for a light rider; a heavy rider who never carries a pillion can ask a service centre whether a small rise suits them.
Zest 110 tyre sizes these figures suit
The Scooty Zest 110 runs a 90/100-10 tyre at the front and a 90/90-10 at the rear, both tubeless. Should your Zest carry non standard sizes, these numbers may not suit it; read the sidewall before filling. For other scooters, our scooty tyre pressure guide and the Jupiter tyre pressure page are good next stops, and the main tyre pressure hub covers every model.
Should a Zest be filled to the sidewall figure?
No. The Zest tyre's moulded maximum marks the ceiling the tyre structure tolerates, nothing more. Pumping a Zest to it gives a jarring ride and less grip. Stick with 24 psi front plus the correct rear value for how many people ride.
Questions owners ask
How much air does a TVS Scooty Zest need?
Riding alone: 24 psi front, 28 psi rear, set cold. Carrying someone: keep 24 psi front and raise the rear to your manual's two-up figure.
Is the TVS Zest pressure the same as the Tata Zest?
No. The TVS is a 110 cc scooter, the Tata a compact sedan. For the car, read the label fixed to its driver side door pillar or its handbook.
How often should a Scooty Zest get a pressure check?
Weekly, plus before any trip out of town. Ten inch tyres hold so little air that a slow seep shows up fast in summer heat.
Can I fill nitrogen in my Scooty Zest?
Yes, though the Zest numbers remain 24 and 28 psi. Plain air kept at those values does the job equally well.
Why does my Zest feel wobbly at the rear?
Low rear pressure is the usual cause. Check it cold and set 28 psi solo. If the wobble stays, have a mechanic look at the tyre, wheel bearing and rear shock.