Skip to content
AutoTyreSize Decode a size

Scorpio N Wheel Cap Size and Fitting

Quick answer17 inch full covers on Z4 and Z6 steel wheels; Z2 has none, alloys use centre caps

Wheels17 inchZ2 bare steelCentre caps on alloysChecked 13 Nov 2026

Independent owner guide. Not affiliated with Mahindra. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

The Scorpio N wheel cap on the Z4 and Z6 is a 17 inch full cover clipping onto the steel rim. The Z2 base model has bare steel rims with no cover, and the Z8S and above use alloy wheels with only a small centre cap.

Covers on a big SUV take a beating from potholes, kerbs and car washes. Most of the covers we replace were knocked loose rather than broken, so fitting them correctly matters as much as buying the right one.

Scorpio N fitment card

Tyre size
245/65 R17 (Z2 to Z8), 255/60 R18 (Z8T and Z8L)
Wheels
17 inch steel (Z2, Z4, Z6), 17 inch alloy (Z8S, Z8), 18 inch alloy (Z8T, Z8L)
Tyre pressure (cold)
Front 34 psi, rear 34 psi (confirm on the driver door sticker)
Wheel cover
17 inch covers on Z4 and Z6 steel wheels, none on Z2
Fog lamps
LED fog lamps from Z8S upwards, none on Z2, Z4, Z6
Silver 17 inch full wheel cover clipped onto the steel wheel of a large SUV, valve stem visible in its slot
A 17 inch full wheel cover over a steel rim, with the valve stem lined up in its slot

Scorpio N wheel cap by variant

VariantWheelCap
Z217 inch steelNone, bare rim
Z4, Z617 inch steel17 inch full cover
Z8S, Z817 inch alloyCentre cap
Z8T, Z8L18 inch alloyCentre cap

If you have a Z2 and want covers, buy the genuine 17 inch set meant for the Z4 and Z6. It fits the same steel rim.

How the 17 inch cover holds on

A full cover has a steel retaining ring behind it, sprung outward, plus plastic hooks around the edge. The hooks lock behind the rim lip and the ring keeps them pressed. On the Scorpio N the cover also has a cut out for the valve stem. If that slot is not lined up, the cover sits proud on one side and works loose.

Before fitting, check the ring is seated in all its hooks and not bent. A bent ring is the top reason covers fly off on the highway.

Fitting a Scorpio N wheel cap step by step

  1. Clean the rim face so no stones sit under the cover.
  2. Line up the valve slot with the valve stem.
  3. Press the cover in at the valve first with both palms.
  4. Work around the edge, tapping with the flat of your hand or a rubber mallet.
  5. Tug lightly at several points; a well seated cover stays put.

Never use a steel hammer; the plastic cracks and the ring kinks.

Genuine or aftermarket covers

The genuine cover is made for this rim profile and holds best. Parts shops also sell 17 inch universal covers, often cheaper and in many designs. Universal covers rely only on the ring, so they suit some rims better than others. Hold one against your wheel in the shop: the hooks should meet the rim lip all round with no big gaps, and the valve slot must reach the valve. some owners secure the cover with a nylon strap wrapped round a steel spoke on rough roads, but keep ties away from the tyre bead.

Alloy centre caps on Z8 trims

Every alloy trim from the Z8S up carries a small clip in centre cap. If one goes missing after a tyre change, ask the service centre for the cap for your rim size; the 17 and 18 inch alloys can use different parts. Fit it with firm palm pressure until it clicks. The cap shields the hub face from grit and spray, so replace a lost one rather than leaving the hole open.

Caring for covers on rough roads

Each time the car comes back from a puncture repair, check the cover was refitted fully. Tyre shop staff are often in a hurry and the valve slot ends up out of line. After a deep pothole, look for cracks around the hooks. Wash covers with plain shampoo; solvent tyre dressings sprayed on the cover dull the silver paint.

For the full rim picture, see Scorpio N alloy wheels and Scorpio N tyre size. The wheel cap hub lists other cars, including the Thar Roxx wheel cap and the older Scorpio wheel cap, and wheel cap size explains measuring.

Questions owners ask

Which cover size suits Scorpio N steel wheels?

A 17 inch full cover fits the steel rims on the Z2, Z4 and Z6. The Z4 and Z6 come with these covers from the factory.

Does the Scorpio N Z2 have wheel caps?

No, Z2 rims are left plain from the factory. The genuine Z4 and Z6 covers can be added later.

Why does my Scorpio N wheel cap keep falling off?

On Scorpio N covers we mostly find a tired, flattened steel hoop, or a valve notch refitted off line after a puncture job. Replace the ring or refit with the slot on the valve, and press all the way round.

Can I fit an 18 inch cover on the Scorpio N?

No. The steel wheel is 17 inch, so only a 17 inch cover fits. The 18 inch wheels are alloys and use centre caps.

Do Scorpio N alloys have centre caps?

Yes, each alloy has a small push fit cap over its hub. Ask the parts counter for the one matching your rim size.