Skip to content
AutoTyreSize Decode a size

Kwid wheel cap size and fitting guide

Quick answer14 inch wheel cap on current Kwids; 13 inch on the earlier version with 155/80 R13 tyres

Wheels14 inch current13 inch earlierThree nut hubChecked 13 Nov 2026

Independent owner guide. Not affiliated with Renault. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

Every current Kwid wheel cap is a 14 inch part, since both the Evolution and the Climber put their 165/70 R14 tyres on 14 inch steel. Owners of the first Kwids, still on 155/80 R13 tyres, need the 13 inch version.

Covers are sold by rim diameter rather than by car model, and the figure after the R on your tyre gives it away. Just remember that a cover with the right diameter but designed for another car might clip on, yet leave the valve hidden or sit crooked around the Kwid's three nuts.

Kwid fitment card

Tyre size
165/70 R14 on every current variant
Earlier version
155/80 R13 on 13 inch wheels
Wheels
14 inch steel with full wheel cover; Climber gets a dual tone styled cover
Tyre pressure (cold)
Front 29 psi, rear 29 psi (check the door sticker)
PCD
3 x 100 mm, three wheel nuts
Wheel cap size
14 inch (current), 13 inch (earlier version)
Silver 14 inch plastic wheel cover being pressed onto a three nut steel wheel of a small hatchback
A 14 inch cover fits every current Kwid steel wheel

Renault Kwid wheel cap by version

VersionTyreWheel cap sizeFactory cover
Evolution165/70 R1414 inchFull wheel cover, sparkling silver
Climber165/70 R1414 inchDual tone styled cover
Earlier version155/80 R1313 inchFull cover

Some owners of early 13 inch cars have since upgraded to 14 inch rims, so glance at the tyre before shopping. A cover one size too small simply will not grip.

Checking which cover your Kwid takes

Crouch by any wheel and find the R on the tyre wall; the digits after it are your rim in inches, and current cars show R14. A tape stretched straight across the rim between the bead seats should read close to 356 mm. Also see how the present cover is fixed. A plain cover snaps on with a sprung steel hoop behind it, while some Climber cars hold the styled cover under the wheel nuts, so it only comes away when those are loosened. Tell the shop which kind you have.

Kwid wheel cap fit with three wheel nuts

Three nuts, not four or five, sit under a Kwid cover. Universal covers shaped for four nut cars often bulge over a nut or bury the valve. Hold the new cover up against the rim in the shop, line the valve with its slot, and confirm it lies evenly all round. If it wobbles in your hand, it will part company with the car on the first bad road.

Pressing a Kwid cover on properly

  1. Get grime off the steel face first so every clip can bite.
  2. Turn the cover over and make sure its sprung hoop is sitting in all the clips and is not kinked.
  3. Turn it so the notch lines up with the tyre valve.
  4. For a snap on cover, engage the upper clips, then press your way down each side using flat palms.
  5. Give a few firm open handed thumps until no gap shows at any point. Never use a hammer.

Why Kwid wheel caps go missing

Covers usually vanish after a fast hit on a crater or speed breaker, a scrape against a high kerb, or a tyre change where the fitter pushed the cover back on half seated. Flooded monsoon streets hide potholes, and a cover can drop off without a sound. A cracked hoop or a snapped clip means it is time for a new cover. As a backup, some drivers loop a zip tie from the cover's vent through an opening in the rim; keep the tie well away from the brake parts and the tyre wall.

Buying a replacement Kwid wheel cap

Single covers and sets of four are both easy to find. The dealer's genuine cover copies the factory design and clips on exactly. Market covers offer more styles and colours, including two tone looks borrowed from the Climber. Thicker plastic and a full metal hoop explain why one cover costs more than another, and they hold up better in summer heat. Skip flimsy shiny covers that go brittle in a few months of sun.

A wheel cover is cosmetic and has no effect on tyre size, pressure or braking. If a broken cover is rubbing the tyre, pull it off until a replacement arrives.

More Kwid wheel pages

Fancy dropping covers for alloys? The Kwid alloy wheels page lists PCD and size options. For rubber, the Kwid tyre size page has the details. Covers in general are explained in our guide to wheel cap sizes, the wheel cap hub has a table of cars, and its sibling car has a Triber wheel cap page.

Questions owners ask

What diameter cover does a Renault Kwid need?

Today's Kwid takes a 14 inch cover, matching its 165/70 R14 tyres. Early cars on 155/80 R13 tyres need 13 inch.

Will a 14 inch cover made for another car suit my Kwid?

Possibly, but the Kwid has three nuts and its own valve spot. Hold it against the rim before you pay to see that it lies flat.

Is the Kwid Climber cover a different size?

Same 14 inch diameter, different design: a two tone pattern instead of the Evolution's plain silver.

Why do my Kwid covers keep coming off?

Most often the sprung hoop behind the cover is bent, a clip has snapped, or it was not pressed fully home after a tyre job. Fit a new cover if any clip is broken.

Can I put 15 inch covers on a Kwid?

No. A cover must match the rim diameter, and a 15 inch cover has nothing to grip on a 14 inch rim.