Skip to content
AutoTyreSize Decode a size

JCB tyre size for 3DX backhoe loaders

Quick answerJCB 3DX rear tyre is 16.9-28; front is 12.5/80-18 on the 3DX Super, 9.00-16 on the older 3DX

Tyre sizesRear 16.9-28Front 18 or 16 inchChecked 13 Nov 2026

Large rear industrial tyre of a backhoe loader on a dusty construction site with deep lug tread

The JCB tyre size on a 3DX backhoe loader is 16.9-28 at the rear, while the front is 12.5/80-18 on the 3DX Super and 9.00-16 on the older plain 3DX. The rear size has stayed the same across the family; the front changed when the machine was updated.

Backhoe loaders spend their life on broken sites, rubble and wet clay, so the ply rating and tread type count for as much as the dimensions. Here we cover each code, how to tell which front your machine needs, and when a site tyre is finished. The car tyre size list also links the other heavy vehicle guides.

At a glance

  • Rear tyre, 3DX family16.9-28, 12 ply rating
  • Front tyre, 3DX Super12.5/80-18 (also written 12.5x18), 12 ply rating
  • Front tyre, older 3DX9.00-16 (also written 9x16), 16 ply rating
  • Why fronts differVersion and market: newer machines use a wider, lower front tyre
  • Rim sizes28 inch rear; 18 inch or 16 inch front depending on version
  • Confirm on your machineSidewall of the fitted tyres, or the operator manual for your serial number

JCB tyre size by version

MachineFront tyreRear tyre
3DX Super12.5/80-18, 12 PR16.9-28, 12 PR
3DX, older version9.00-16, 16 PR16.9-28, 12 PR
3DX Xtra and other versionsCheck the fitted tyre or the manual16.9-28 on the machines we checked

The 3DX Super figures come from the maker's own brochure, which also lists an optional heavy duty rear. The older 3DX figures come from published specification listings and tyre makers' backhoe ranges. We could not find a published front size for every version, so treat the last row as a prompt to check, not a figure.

JCB rear tyre size: 16.9-28 explained

16.9-28 is written in inches: close to 16.9 inches of section width, mounted on a 28 inch wheel, with the hyphen standing for bias construction, the usual type for backhoe rear tyres in India. The rear tyres carry the backhoe arm and most of the digging load, so they use a deep industrial lug pattern and a 12 ply rating on the 3DX. Rear tyres are heavy; changing one is a job for a tyre shop with a proper bead breaker, not a roadside fitter.

JCB front tyre size and the 3DX front tyre

The 3DX front axle steers and carries the loader bucket. On the 3DX Super the front tyre is 12.5/80-18: about 12.5 inches wide with an 80 percent profile on an 18 inch rim. Some listings write it as 12.5x18, which is the same tyre. Older 3DX machines use 9.00-16, a narrower front about 9 inches wide on a 16 inch rim with a higher 16 ply rating.

The two fronts are not interchangeable without changing the wheel, because the rim sizes differ. Check what is moulded on the existing front tyre before you order; if it has been changed, the operator manual for your serial number is the reference.

Ply rating and tread for site work

The PR figure is a strength rating for the casing. Dropping to a weaker casing saves nothing; it cuts faster on rebar and stone and can burst under a full bucket. For quarry and demolition work, ask for a cut resistant industrial tread. For mostly road travel between sites, a tread that runs quieter on tar lasts longer. Road tyre load ratings are covered on the load index page.

Pressure on a backhoe loader

Inflate cold to whatever the operator manual specifies. Backhoe tyres often run different front and rear pressures because the bucket loads the front and the backhoe loads the rear. Check them every morning before work, not after the machine has been moving on hot tar. Underinflation folds the sidewall under the bucket load and cracks it; overinflation makes the machine bounce while travelling and reduces grip on soft ground. If your gauge reads in bar, the pressure converter changes it to psi.

When to replace a backhoe tyre

  • Lugs worn so low the tyre slips on wet clay or slopes.
  • Cuts that reach the cords, or cords visible on the sidewall.
  • A bubble anywhere on the casing.
  • Cracks at the base of the lugs or around the bead.
  • Repeated air loss after a repair.

Bulges or exposed cords ground the machine until a tyre shop has examined it. Move the machine slowly and unloaded to a safe spot. Replace rear tyres as a pair so the machine sits level when digging.

Questions owners ask

What is the JCB 3DX rear tyre size?

16.9-28 with a 12 ply rating. The maker's brochure for the 3DX Super lists this size, and older 3DX machines use the same rear.

What is the JCB 3DX front tyre size?

12.5/80-18, also written 12.5x18, on the 3DX Super. The older 3DX uses 9.00-16 with a 16 ply rating. Check the sidewall of your fitted tyre to see which your machine has.

Will a 12.5/80-18 front go on an older 3DX?

Not on the same wheel, since the older 3DX uses a 16 inch front rim. A change would need the matching 18 inch wheels. Ask the dealer whether that combination is approved for your machine.

Is a tractor 16.9-28 tyre the same as a backhoe 16.9-28?

The size matches, but the tread and ply rating are made for different work. Use an industrial backhoe tyre with the ply rating the maker specifies.

Where is the tyre size on a JCB machine?

Moulded on the sidewall of each tyre, and in the operator manual's spec section for your serial number.