Sized at 16 inches, the Creta wheel cap hides the steel wheels of the base E trim. It hides the pressed steel rim and the wheel nuts, and gives the base SUV a cleaner look.
Covers get lost more often than any other exterior part. A deep pothole, a hard kerb or a bad tyre change can pop one off. Below: confirming the size, buying the correct cover, and seating it so potholes cannot shake it free.
Creta fitment card
- Tyre size
- 205/65 R16 (E, EX, S), 215/60 R17 (S(O), SX, SX Tech, SX(O)), 215/55 R18 (N Line)
- Wheels
- 16 inch steel on E, EX, S; 17 inch alloy on S(O) and SX trims; 18 inch alloy on N Line
- Tyre pressure (cold)
- Front 33 psi, rear 33 psi at normal load; confirm on the driver door sticker
- PCD
- 5 x 114.3 mm, centre bore 67.1 mm
- N Line spare
- 215/60 R17 on a steel wheel
- Front fog lamps
- Not fitted on the current Creta; earlier version had them in the bumper
- Wiper (driver side)
- 24 inch (600 mm); measure the passenger blade
- Wheel cap
- 16 inch, on the base E trim with steel wheels

Which Creta has a wheel cap
Only the base E pairs its 16 inch steel rims with these clip on covers. Most listings show the EX and S on 16 inch styled steel, and one lists the EX with covers too, so check what yours actually wears. Trims from the S(O) upward use alloys with a small centre cap instead. An alloy wheeled Creta takes a small hub badge cap instead of a full cover.
Confirming the cover size for your Creta
Read the tyre sidewall. If it says 205/65 R16, the rim is 16 inches and the Creta wheel cap must be 16 inch. Covers made for 15 or 17 inch rims simply won't seat. Some covers also carry a moulded size on the inside. Do not measure the cover itself, since the lip makes it look larger than the rim.
The rim to cover rule for any car is in our wheel cap size guide.
Genuine Creta wheel cap versus aftermarket
A genuine cover matches the factory spoke design and has clips shaped for the Creta rim. Aftermarket covers often use a single steel wire ring that holds the cover by tension. Both work when the size is right. Request a Creta 16 inch cover at the counter, and make sure its valve slot matches your valve position before leaving.
Cheaper plastic yellows and goes brittle under strong sun, and that sun resistance is the main reason one cover is priced higher than another.
Fitting a Creta wheel cap at home
- Wipe the rim face so dust does not stop the clips seating.
- Turn the cover so its valve slot sits over the tyre valve.
- Push the upper edge home first, then press around the rim with an open hand.
- Tap the lower edge firmly until each clip snaps in.
Never hit the cover with a hammer. It cracks the clips.
Why Creta covers fly off
Broken clips, a bent rim edge or the wrong size are the usual causes. After a puncture, roadside shops sometimes refit the cover in a hurry. If a cover keeps coming loose, a pair of nylon cable ties through the spokes and around the steel wheel holds it in place. Keep the ties thin and cut the ends short.
Safety check when the cover is off
Whenever a cover is removed, look at the steel rim. Rust around the nuts, a ding along the rim lip or a loosened nut is a job for the tyre shop before your next trip. Have the nuts torqued after any wheel change.
Sizes for the tyre behind it appear in the Creta tyre size rundown. If you plan an upgrade, see Creta alloy wheels, and our wheel cap hub covers other cars.
Questions owners ask
What is the Creta wheel cap size?
Sixteen inches, matching the steel rim on the base E. The tyre size on that wheel is 205/65 R16.
Will a Venue wheel cap fit the Creta?
Most Venue steel wheels with covers are 15 inch, so the cap is too small. Buy a 16 inch cover made for the Creta.
Can I fit wheel covers on Creta alloys?
No. Full covers clip onto steel rims only. Alloy wheels use a small centre cap that snaps into the hub opening.
Do I need to buy all four Creta wheel caps?
You can buy one, but the design may not match if the factory style has changed. Many owners buy a set so all four look the same.
My Creta wheel cap rattles, why?
Usually one clip has snapped or sits outside the rim lip. Remove the cover, check every clip and refit it, or replace the cover if clips are missing.