Skip to content
AutoTyreSize Decode a size

Tata Altroz Alloy Wheels: Size, PCD and Upgrades

Quick answer16 inch alloys on Accomplished trims, PCD 4 x 108 mm, with 185/60 R16 tyres

Wheels185/60 R16 tyres4 nuts per wheelDual tone finishChecked 13 Nov 2026

Independent owner guide. Not affiliated with Tata Motors. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

The Altroz alloy wheels are 16 inch dual tone rims found on the two Accomplished trims, wearing 185/60 R16 tyres and bolting on with a PCD of 4 x 108 mm. Every cheaper trim rolls on 16 inch steel of identical diameter, so an alloy upgrade needs no change of rubber.

Looking back at the earlier version, the XZ and XZ+ wore 16 inch diamond cut alloys, while the Racer got gloss black ones. Entry XE and XE+ cars stood on 14 inch steel, which means those owners must budget for tyres along with the rims.

Altroz fitment card

Tyre size
185/60 R16 on every current variant
Wheels
16 inch steel (Smart to Creative S), 16 inch alloy (Accomplished trims)
Tyre pressure (cold)
Front 32 psi, rear 32 psi
Full load pressure
Front 35 psi, rear 35 psi
Spare
165/80 R14 steel space saver
PCD
4 x 108 mm
Wiper blades
24 inch driver side, 16 inch passenger side
Earlier version base tyre
165/80 R14 on XE and XE+ with 14 inch steel wheels
Dual tone 16 inch alloy wheel with black and machined silver spokes on a hatchback, four wheel nuts visible
Four nuts on a 108 mm circle hold each factory alloy in place

Factory wheels by trim

VariantWheelTyre
Smart16 inch steel185/60 R16
Pure, Pure S, Creative, Creative S16 inch steel with covers185/60 R16
Accomplished S, Accomplished+ S16 inch dual tone alloy185/60 R16
Earlier version XZ, XZ+16 inch diamond cut alloy185/60 R16
Earlier version Racer16 inch black alloy185/60 R16
Earlier version XE, XE+14 inch steel165/80 R14

PCD and what else must match

Four nuts spaced around a 108 mm circle clamp each Altroz wheel, written 4 x 108 mm. Several other popular hatchbacks use 4 x 100 instead, so a lot of wheels on a shop shelf simply will not line up. Spacers with wobble bolts, or adaptor plates, are no fix for a mismatched pattern.

  • Centre bore: the central hole should hug the hub, either directly or with a properly sized spigot ring. A loose fit shows up as shake through the steering above 80 km/h.
  • Offset: sets how far the rim sits towards the arch. Push it out too far and the tyre rubs the lip; pull it in and the inner edge may foul the suspension strut.
  • Load rating: confirm the wheel is certified for a fully laden family hatch, not just the bare kerb weight.

Our PCD calculator helps confirm a bolt pattern, and PCD full form explains the term.

Adding Tata Altroz alloy wheels to a steel wheel car

Smart, Pure and Creative owners can bolt on the factory 16 inch alloys directly, keeping their 185/60 R16 tyres. Wheels bought through a dealer carry the correct hub fit and offset. Order the matching alloy nuts at the same time, because the nuts used on steel rims seat at a different angle and can work loose on an alloy.

Someone upgrading an earlier XE or XE+ from 14 inch steel will also need a set of four 185/60 R16 tyres. Overall diameter differs from the old 165/80 R14 by only about 1.3 percent, and the speedo reading moves very little.

Going to 17 inch: is it worth it

Some owners fit 17 inch aftermarket alloys with 205/45 R17 tyres. Its diameter falls short of the factory tyre by roughly 1.9 percent, inside the 3 percent limit. On Indian roads the downsides add up:

  • Thinner sidewalls pass every speed breaker thud straight into the cabin.
  • A sharp pothole edge can dent or crack the rim lip.
  • Low profile replacements are dearer, and a small town tyre dealer may not stock them.
  • The wheel feels heavier to twirl in a tight parking lot.

Tata does not offer 17 inch wheels on the Altroz. Let your insurer know in writing about non factory wheels, or a later claim could be argued over. For the wider picture, see 17 inch alloy wheels explained.

Looking after dual tone and diamond cut finishes

The machined silver face on these wheels has only a thin clear coat. When a stone chips that lacquer, damp creeps beneath it and a chalky bloom starts to grow.

  1. Wash wheels when cool with mild car shampoo; avoid acid cleaners.
  2. Use a separate soft brush for wheels so grit from the body does not scratch them.
  3. Clean brake dust weekly, more often in the rains.
  4. Touch up small chips quickly to stop corrosion.

Scraping a kerb while parallel parking is the commonest damage. A wheel specialist can put the rim on a lathe and cut a fresh shiny layer; our diamond cut wheels page explains how.

Bent or cracked rims

Watch for a shimmy through the steering on the highway, an Altroz tyre that goes soft every week, or a dented section on the inner rim edge. Any of these calls for a balancing machine check at a tyre shop. Many bends can be pressed back true; cracks call for a new wheel.

A cracked or badly bent rim should only be driven gently to the closest workshop, never on a long run.

Questions owners ask

What size are tata altroz alloy wheels?

16 inch on the Accomplished trims of the current car and on the XZ, XZ+ and Racer of the earlier version. All of them run 185/60 R16 rubber.

What is the Altroz PCD?

4 x 108 mm. Several rival hatchbacks use 4 x 100, so confirm the pattern before paying.

Can I fit alloys on the Pure or Creative?

Yes. Factory 16 inch alloys go straight on and you keep your present tyres. Buy the alloy type nuts with them.

Is a 17 inch upgrade sensible?

Aftermarket 17 inch wheels with 205/45 R17 tyres keep the diameter close, but the ride turns stiffer and the rims suffer more on broken roads. Tata does not fit this size.

Can diamond cut wheels be repaired?

Scuffs and kerb rash can be re machined by a specialist. Cracked wheels should be replaced.