Skip to content
AutoTyreSize Decode a size

Ntorq Spark Plug: Finding, Checking and Changing It

Quick answerOne plug in the 124.8 cc engine; confirm type and gap in the owner's manual

Bike gearCheck the manualCopy the old plugChecked 13 Nov 2026

Independent owner guide. Not affiliated with TVS. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

The Ntorq spark plug is a single plug serving the 124.8 cc air cooled engine, with its type code and gap listed in the owner's manual. We have not found two reliable sources that agree on one part code, so read the manual or the plug you remove rather than trusting a list.

This page shows where the plug sits, how to read the old one, and how to change it without damaging the cylinder head threads.

Ntorq 125 fitment card

Tyre size
Front 100/80-12, rear 110/80-12, tubeless
Wheels
12 inch alloy, front and rear
Tyre pressure (cold)
Front 24 psi, rear 28 psi solo; rear 36 psi with pillion
Battery
12 V, 4 Ah maintenance free
Front brake
220 mm disc (disc variants) or 130 mm drum (drum variant)
Rear brake
130 mm drum
Engine
124.8 cc single cylinder, air cooled
Used spark plug with a light tan electrode and a feeler gauge on a workshop bench next to a plug spanner
A light tan tip means a healthy engine; copy the code from the old plug before buying.

Finding the right ntorq spark plug code

  • Owner's manual: the specifications page gives the plug type and the gap.
  • The old plug: the code is printed on the white insulator. Copy it exactly, including any letters at the end.
  • A TVS service centre: they can confirm the part for your chassis number.

The code tells the shop the thread size, reach and heat range. A wrong heat range makes the engine run too hot or foul the plug, and a wrong reach can hit the piston.

Where the plug sits on a scooter engine

On a scooter the engine hangs under the rear body, so the plug is reached through an inspection flap under the seat storage or from below beside the engine. Look for the thick black ignition lead with a rubber cap on the end; the plug sits under that cap. Let the engine cool fully first, since aluminium heads and plug threads are easy to strip when hot.

Changing the plug step by step

  1. Pull the cap straight off by its rubber boot, not the wire.
  2. Clear grit from around the plug base with a brush or air so none drops inside.
  3. Loosen it anticlockwise using a spark plug spanner.
  4. Check the new plug's gap with a feeler gauge against the manual figure.
  5. Thread the fresh plug in with fingers for a few turns to avoid cross threading.
  6. Snug it down with the spanner and push the boot on till you feel a click.

Reading the old plug

LookLikely meaning
Light tan or grey tipEngine healthy
Dry black sootRunning rich, choked air filter or lots of idling
Wet oily depositsOil getting past rings or valve seals
White blistered tipRunning hot or lean
Rounded worn electrodePlug due for replacement

Oily or white plugs point to engine problems a new plug will not fix; show them to a mechanic.

Signs the Ntorq needs a new plug

Hard starting on cold mornings, a hesitation when you open the throttle from a signal, a rough idle and falling mileage all suggest a worn plug. A misfire on the Ntorq feels like a stutter at steady speed. Fuel injection hides some plug wear, so many owners swap it at the service book interval instead of waiting for trouble.

Iridium upgrades

Iridium plugs have a very fine centre electrode and last longer than standard nickel ones. On a commuter scooter the gain is mostly a longer change interval rather than more power. If you fit one, it must match the original thread, reach and heat range. Read more in our iridium spark plug guide.

When starting trouble is not the plug

If a new plug does not help, check the battery, since a weak one cannot spin the starter fast enough; see Ntorq battery size. Stale fuel after a long stop and a blocked air filter are also common. Our spark plug guide explains gaps and heat ranges in detail.

Questions owners ask

Which spark plug does the Ntorq 125 use?

The type is listed in the owner's manual and printed on the plug itself. Copy that code exactly, or ask a TVS service centre to confirm it for your chassis number.

How many spark plugs does the Ntorq have?

One. The 124.8 cc engine is a single cylinder unit with a single plug.

How often should I change the Ntorq spark plug?

Follow the interval in your service book. Change it sooner if starting gets hard or the engine stutters.

Can I clean and reuse an old plug?

A light brush can remove soft soot, but a worn, rounded electrode needs a new plug. Never sandblast or file a plug.

Is an iridium plug worth it in an Ntorq?

It lasts longer, but adds little power on a commuter scooter. Pick one only if thread, reach and heat range all match the stock plug.