Skip to content
AutoTyreSize Decode a size

Iridium Spark Plug for Hunter 350: What to Match

Quick answer12 mm thread plug gapped 0.7 to 0.8 mm; an iridium plug must match the listed heat range

Bike gear12 mm threadGap 0.7 to 0.8 mmChecked 13 Nov 2026

Independent owner guide. Not affiliated with Royal Enfield. Figures checked against the maker's published details; confirm on your vehicle's door sticker or manual.

An iridium spark plug for Hunter 350 must have the same 12 mm thread, reach and heat range as the plug listed in the owner's manual, with the electrode gap set between 0.7 and 0.8 mm. The manual lists conventional plug codes and does not ask for iridium, so an iridium plug is an upgrade you choose, not a requirement.

The quickest way to buy the right one is to read the code printed on the plug already in your engine, or to show the specifications page of your manual at a parts shop. They can cross match it to an iridium version of the same heat range.

Hunter 350 fitment card

Front tyre
110/70-17 54P tubeless (alloy wheels); 100/80-17 52P tube type (Retro, spoke)
Rear tyre
140/70-17 66P tubeless (alloy wheels); 120/80-17 61P tube type (Retro, spoke)
Wheels
17 inch front and rear; cast alloy on Metro, wire spoke on Retro
Tyre pressure (cold)
Front 29 psi, rear 32 psi solo; front 29 psi, rear 36 psi with pillion
Front brake
300 mm disc, twin piston floating caliper
Rear brake
270 mm disc with dual channel ABS; 153 mm drum on Retro (single channel ABS)
Battery
12 V, 8 Ah VRLA maintenance free
Spark plug gap
0.7 to 0.8 mm, 12 mm thread
New iridium spark plug with fine centre electrode resting on the finned cylinder head of an air cooled single cylinder motorcycle
The thin iridium tip needs a gap of 0.7 to 0.8 mm on this engine

Hunter 350 spark plug facts from the manual

ItemWhat the manual gives
Thread12 mm
Electrode gap0.7 to 0.8 mm
Plug typeTwo approved plug codes from parts makers, neither an iridium type
IgnitionElectronic fuel injection with electronic ignition
ToolBox spanner for the plug, in the bike tool kit

The plug sits on the cylinder head of the air oil cooled 349 cc single. The same plug details apply to the Metro and Retro, since both share one engine.

Choosing an iridium spark plug for Hunter 350 riders

An iridium plug has a very thin centre electrode tipped with a hard, heat resistant metal. A thin tip needs less voltage to fire and keeps its shape far longer than a nickel tip. On a long stroke single like the J series engine, owners notice it mostly as a quicker catch on chilly mornings and steadier idling at signals.

It will not add real power to a healthy engine. If your bike starts first press and idles evenly, a fresh standard plug of the listed type does the job. The iridium plug pays back mainly in longer life between changes.

Matching the plug correctly

  • Heat range: the single most important match. A hotter plug can cause knocking under load; a colder one fouls with carbon in slow city traffic.
  • Thread and reach: a longer reach than stock can foul the piston, a shorter one leaves the tip hidden in its bore.
  • Resistor type: the Hunter has a digital meter cluster and a fuel injection computer, so keep the same resistor or non resistor type as the stock code. A mismatch can cause electrical noise.

A good parts counter will look up the iridium equivalent from the same plug maker as your stock code. If they guess, go elsewhere.

Changing the plug at home

  1. Park the bike on level ground and let the engine cool completely. Aluminium head threads strip easily when hot.
  2. Pull the plug cap straight off. Do not tug on the lead.
  3. Blow away dust around the plug with a brush so grit cannot drop down the plug hole.
  4. Undo the plug anticlockwise with the box spanner from the tool kit.
  5. Check the gap on the new plug with a wire gauge: 0.7 to 0.8 mm.
  6. Thread it in by hand for several turns, then finish with the spanner to the tightening torque the manual specifies.
  7. Press the rubber cap back over the terminal till it sits snugly.

Our spark plug spanner page explains which tools grip without cracking the ceramic.

Setting the gap on a fine iridium tip

New iridium plugs usually leave the box already gapped, but for a range of engines, so measure. If the gap is outside 0.7 to 0.8 mm, bend only the outer ground strap, and only a little at a time. Never press a feeler blade hard against the thin centre tip, and never tap the plug on the floor to close the gap. A cracked tip can drop into the cylinder.

What the old plug tells you

Tip colourLikely meaning
Light brown or greyNormal running
Dry black sootRich mixture, dirty air filter or lots of short trips
Wet and oilyOil getting past rings or valve seals
White, blisteredRunning hot or wrong heat range

An oily or white plug points to a fault the new plug will not fix. Get the bike checked at a service centre.

Signs your Hunter needs a new plug

  • It needs several presses of the starter on cold mornings.
  • Jerks or misses when you open the throttle in third gear.
  • Idle rises and falls at a traffic light.
  • Fuel economy drops on the same commute.

These signs can also come from a weak battery, so check the Hunter 350 battery too. The plug change interval is in the periodic maintenance chart of your manual.

Questions owners ask

Which spark plug does the Hunter 350 use?

The owner's manual lists two conventional 12 mm thread plug codes with a 0.7 to 0.8 mm gap. Read the code on your current plug or the manual's specifications page and ask a parts shop for that code.

Does the Hunter 350 gain anything from iridium?

It gives easier cold starts and lasts longer. It does not add noticeable power. It is worth it if you ride a lot and want fewer plug changes.

What is the Hunter 350 spark plug gap?

Between 0.7 and 0.8 mm, as stated in the owner's manual. Use a round wire feeler to confirm it before any new plug goes in.

Will a hotter iridium plug improve pickup?

No. A different heat range than listed can cause knocking or fouling. Stay with the heat range of the stock plug.

Can I fit the plug myself?

Yes, if the engine is cold and you start the thread by hand. If you feel resistance in the first turns, stop and have a mechanic look, because a crossed thread in the head is an expensive repair.