For the i10 wheel cap, buy 13 inch full covers, because every steel wheel variant of the original i10 runs 13 inch rims with 155/80 R13 tyres. That covers the D Lite, Era, Magna and Sportz; Asta cars rolled out on 13 inch alloys and skip covers.
Covers on this model often crack or fly off after years of potholes and kerb scrapes. You can replace one at a time, but a matched set of four looks far better.
i10 fitment card
- Tyre size
- 155/80 R13 on every variant, D Lite to Asta
- Wheels
- 13 inch steel with full cover on lower variants, 13 inch alloy on the Asta
- Tyre pressure (cold)
- Front 33 psi, rear 33 psi (normal load)
- PCD
- 4 x 100 mm, four nuts
- Wheel cap
- 13 inch full wheel cover on steel wheel variants
- Wiper blades
- 22 inch driver side, 16 inch passenger side
- Status
- No longer sold new; Grand i10 and Grand i10 Nios followed it

i10 trims that wear plastic covers
| Variant | Rim | Cover needed |
|---|---|---|
| D Lite, Era | 13 inch steel | 13 inch full cover |
| Magna | 13 inch steel | 13 inch full cover |
| Sportz | 13 inch steel | 13 inch full cover |
| Asta | 13 inch alloy | None, small centre cap only |
The boot spare stays bare steel. Leaving it uncovered is fine, but if you move it to the road after a puncture you can clip a spare cover on.
Confirming the size on your car
The tyre wall answers it: digits after the R are the rim, which should read 13 on this Hyundai. If a previous owner fitted 14 inch rims, you will see R14 instead and need 14 inch covers. Do not go by the old cover, as some aftermarket covers carry no size marking.
Hyundai i10 wheel cap original or aftermarket
An original cover from the Hyundai parts counter matches the factory style and the retaining clip shape, and usually lasts longer under Indian heat. It costs more, and since this hatch went out of production, the exact design may be hard to find. Aftermarket 13 inch covers come in many designs. A thicker, flexible plastic survives potholes better than a thin shiny one that cracks the first time it hits a kerb.
How to fit a cover so it stays on
- Brush grime and loose rust off the steel face.
- Rotate the cover until the valve sits in its gap.
- Seat the steel retaining ring evenly in the clips.
- Press the cover in with flat palms, working around the edge, never with a hammer.
- Check it sits flush all round and the valve is reachable.
Plenty of owners loop a nylon tie between cover spokes and the rim holes. This helps on rough roads, but cut the tie away before a tyre shop removes the wheel.
Why covers fall off and what to check
Covers mostly drop off after a deep pothole strike, a warped wire ring or a snapped clip. Inspect the steel rim whenever one goes missing, since a dented lip also brings a slow air leak and wobble at speed. If you see a bend or a cut on the tyre, ask the tyre shop to inspect the wheel before you drive far.
Switching to alloys
Tired of replacing plastic, some i10 owners move to alloy rims. The Asta already had 13 inch alloys, so that rim size is the safe choice. Read the i10 alloy wheels page for bolt pattern and rim sizes, the i10 tyre size page for tyres, and the wheel cap guide for types and materials.
Questions owners ask
Which cover size suits the Hyundai i10?
Choose 13 inch. All steel rim trims measure 13 inch.
Can I fit a 14 inch wheel cap on my i10?
No, a bigger cover cannot clip onto the smaller rim. Match the cover to the rim figure printed after R on your tyres.
Is an original Hyundai i10 wheel cap still available?
Production ended long ago, so stock varies. Quote your chassis number at a Hyundai workshop parts desk; a parts shop may offer a close aftermarket match.
Why does my i10 wheel cover keep falling off?
The steel ring may be bent or a clip may be broken. Replace the cover or its ring, and have the rim checked if it hit a pothole.
Do wheel covers affect the tyres?
No, they are cosmetic. Make sure the valve stays reachable so you can check air easily.